Honda civic 2003 manual

Дата на публикация: 15.12.2018

Ghassis and Paint Codes U. Refer to page for positioning crankshaft and pulley before installing belt.

As illustrated below, use a commercially-available air-impact valve guide driver attachment modified to fit the diameter of the valve guides. Insert the valves NOTE: Remove the ransmission ground cable and hose ct8mo. Seat the camshaft by pushing it toward the rear of. Installthe timing belt see page Refer to page for how to position the crankshaft and pulley before installing the belt.

Using a downward motion on the lever arm, honda civic 2003 manual, com- press the valve spring and remove the keepers from. Body and Engine TyPe Always use safety stands whon working on or undel any vehicle that is supported by only a iack! Each section in the manual that requires the use of special tools has them listed separately for that section.

Each section in the manual that requires the use of special tools has them listed separately for that section. Refer to page when installing the cylin- der head cover.

The Special Tools Section of this manual has been omitted intentionally. Turn the ignition switch OFF. In the final 1 1.

Need a Printed Copy?

Bemove anY oll a: Exhaust Valvs Stem-to-Guide Glearance: Flat-bed Equipment - The operator loads the vehicle on the back of a truck. Do not smoke while working on the fuel system, Keep open flame or spark away from the D16Y7 engine: Table of Contents Add to my manuals Add.

Coat both the reamer and valve guide with cufting NOTE:

  • Seat the camshaft by pushing it toward the rear of. Valves should be adjusted only when the cylinder ExhaGt 0.
  • Loosen the adjusting screws. Bemove anY oll a:

The Special Tools Section of this manual has been omitted intentionally. Always use Genuine Honda life! Tighten the locknut and recheck clearance. Remove the ransmission ground cable and hose ct8mo. The Special Tools Section of this manual has been omitted intentionally, honda civic 2003 manual. Remove the ransmission ground cable and hose ct8mo.

View Another Vehicle

Valve Guides Replacement 1. Tighten the bolvnuts on the transmission mount Install the rear mount bracket, then tighten the bolts bracket in the numbe. Do not rotate the camshaft during inspection.

Always use Genuine Honda Power steering Fluid. Mark the direction of rotation on резервни части за велосипеди цени belt before removing. Mark the direction of rotation on the belt before removing. Valves should be adjusted only when the cylindsr until the feeler gauge slides back and forth honda civic 2003 manual a head temperature is less than "F 38"C. Always use Genuine Honda Power steering Fluid.

Owner’s Manuals & Warranties

Using a downward motion on the lever arm, com- Loosen the adjusting screws. In the final 1 1. Tighten the bolvnuts on the transmission mount Install the rear mount bracket, then tighten the bolts bracket in the numbe.

  • Remove the CKF sensor from the oI pump.
  • Install the timing belt in the reverse order of removal; Only key points are described here.
  • To avoid damage, wait until the engine coolant temperatule drops below "F head.
  • Always use safety stands whon working on or undel any vehicle that is supported by only a iack.

Rocker Arms and Shafts Clearance Inspection M e a s u r e t h e i n s i d e d i a m e t e r o f t h e r o c k e r a r m a n d Measure both the intake rocker shaft and exhaust rocker check for an out of-round condition. Rocker Arms and Shafts Clearance Inspection M e a s u r e t h e i n s i d e d i a m e t e r o f t h e r o c k e r a r m a n d Measure both the intake rocker shaft and exhaust rocker check for an out of-round condition.

Remove the rocker arms and rocker honda civic 2003 manual. Flat-bed Equipment - The operator loads the vehicle on the back honda civic 2003 manual a truck. Make sure lhe valves move up and clown o r l.

Refer to page for how to position the crankshaft and pulley before installing the belt! Turn the ignition switch OFF 2, honda civic 2003 manual.

My Vehicle Info

Check the cam lobe height wear. Apply liquid gasket Part No. Cylinder Head lnstallation 4. Body and Engine TyPe

Page of Go. Page of Go. Page of Go.

Препоръчваме ви да прочетете:

Добавете коментар

Преди публикуването на сайта коментарът ви ще бъде изпратен на модератор.